Single-Seven and Ruger's customer service

Wrote Ruger about the problems with the Single-Seven and got a quick response. Called as instructed and got an RMA number and shipping label e-mailed to me. Sent the revolver back on Tuesday afternoon. Ruger says 2-3 week turn-around. So far they have lived up to their reputation for wonderful customer service. Not every mass produced item is going to be perfect. I'm optimistic about this and will note progress as it occurs.

Range day...

14 shots at 25-yards, 100 gr. Federal load

Several months ago now I bought a new Ruger Single-Seven, 5½", stainless steel, .327 Federal, single-action revolver. I really haven't been all that enthused with it. I DO like the trajectory of the .327 Federal round and the light recoil and it holds the promise of being a good 100 yard varmint gun to carry in the field with the ability to shoot .32 S&W Long for edible small game. But...

When I first shot it I had nothing but Federal factory 85 gr. bulleted ammunition and was later able to get some of the 100 gr. bulleted ammunition. Both bullets are flat-nose soft-points (jacketed) and look the same while in the case but the 85 gr is obviously a bit shorter. Some cases seemed to be a bit fat near the case head and didn't chamber easily but now I am convinced that one must precisely locate the cylinder to avoid the rim rubbing on the side of the loading cut in the recoil shield. That is not too great a difficulty to prevent me from liking the gun, but...

I noticed with both loads that it seemed there would be 6 or 7 different groups on the target. I am not an "expert" shot but I can usually kill squirrels with pistols at up to 25-yards despite the inevitable vision changes that come with old age and I have to ask, how can I get 6-7 different groups if I can't shoot the gun well enough to get the one group one would expect? I thought perhaps that the chambers differed significantly from one another.

You can see those differences in a couple of ways aside from the 6-7 different groups. One way is in the burn marks on the front of the cylinder. Because of the size of the cylinder and the quantity of gas produced by the cartridge one has distinctive burn marks on the side of the cylinder by each chamber where some gas is directed down the side of the cylinder by the top strap. This is likely where the "spitting" is mostly originating. I don't know if this is avoidable or not but in any case the patterns of these burn marks are different for each chamber and the larger marks come from those chambers with the apparently largest throats.

Yes, those throat dimensions differ for each chamber. I don't have a set of plug gauges, the ideal way to check this out, but I do have a variety of bullets intended for this cartridge and/or its .32 caliber brethren (.32 S&W, .32 S&W Long, .32 HR, and .32-20). I tried the "drop test" in that I took each of those bullets, measured them with my dial calipers (after ensuring they were properly calibrated) and found that there were 2 chambers whose throats were considerably tighter than the other 7. These 2 chambers also had the smallest burn marks on the side of the cylinder. Both the Speer and Hornady 100 gr. bullets marked .312" and measuring .3115-.3112" dropped all the way through every throat but for those two chambers. I was a bit surprised that cast bullets of the same dimensions did not and don't know why this is so but suspect the lube gripped the throats just enough to prevent their passing. The barrel throat does not permit these same bullets to get so far as to pass the ogive.

That's not the only problem with this gun though. Sometimes, especially immediately after shooting, the action will not cycle. My impression is that something has been knocked out of kilter inside. My first thought was that fired primers were dragging on the recoil shield or that the case head itself had hung up on one of the slight hole edges in the recoil shield. However, I was able to duplicate this "freezing" or "locking up" of the action with an empty chamber even without the cylinder installed.

So, what to do? Well, the gun was bought new, has not been altered, has never had other than factory ammo fired in it and it isn't good enough so it is going back to Ruger. It won't be fired again until it comes back from them.

Adventures in reloading...

I had a bit of an oddity while reloading today. I've been working on loads for my M1 rifle and settled on 48 gr. 4064 with the 150 gr. Sierra Matchking. Since my old Lee Autoprime was getting a bit loose (the cover which would sometimes work loose) I thought I'd try a new one. The new Autoprime has a two stage system to separate the primers you are seating from those in the "magazine" and it takes out some of the feel. Also, in my load search I sought to compare to a widely known quantity, the Hornady 168 gr. AMAX load. All this came together today when I went to charge one of the Hornady cases as I picked up the primed case to pour in the powder charge I noticed that the primer was falling out! Although I had this happen once with a many times fired case about 30 years ago I have never had this happen with a once fired case. None of the other 39 cases had a loose primer pocket and I didn't notice this when removing the fired primers and I think, emphasis on think, that I didn't notice the lack of resistance when priming due to the built in multiple stages of the Autoprime.

About that new Autoprime... The primer "magazine" cover has come loose twice or rather it was pushed off by the first stage primer lifter catching the primer on the cover and pushing it off. There is some slop there and it bugs me. I guess Lee had to do something because somewhere, somehow, somebody managed to set off a primer while priming and thence the whole lot in the "magazine" yet this system doesn't thrill me. I'm thinking of buying an RCBS hand primer.

Range day...

Back to the range this afternoon with the M1 rifle. Easy to stay on a 1/2 silhouette at 100 yards with some loads grouping into ragged silver dollar sized groups. Was able to shoot another 1½-inch group with the .223 10-inch Contender. Took the new Contender with 10-inch .22 LR barrel and even did pretty well with it at 100 yards shooting a 3-inch group with the scope set at 4-power. All shooting with of the .22 LR was done with Winchester PowerPoint ammo. Easy to keep on a squirrel head out to 50-yards.

I am going to switch from H4895 to IMR 4064 for the M1, .30-06 loads. Both versions of 4895 being more difficult to get right now I'd rather save what I have for other cartridges.

We had a bit of a thundershower but while we listened to and watched the fireworks for about 30-minutes we only had about 5-10 minutes of rain and not really enough to wet anything.